Dispositivo de obturación de gutapercha Woodpecker / DTE Fi-E y Fi-P Plus (blanco)

Dispositivo Fi-E:

Inalámbrico y eléctrico

Fluidez perfecta de la gutapercha, salida uniforme y suave de gutapercha sin burbujas. Más fácil que la inyección manual tradicional de gutapercha para aliviar la fatiga de las manos del operador. Elimina los riesgos quirúrgicos causados ​​por fugas y desbordamientos de gutapercha. Mantenimiento gracias a la limpieza automática de la gutapercha restante.

Aguja de inyección reutilizable

Rotación de 360°. 3 velocidades de inyección. La barra de gutapercha se carga directamente en la aguja de inyección. No quedan residuos de gutapercha en el interior de la máquina, lo que facilita su limpieza. La barra de gutapercha se puede sustituir en cualquier momento sin tener que esperar a que se enfríe la máquina interna.

Diseño de botón doble

Botones de inyección dual diseñados simétricamente, sensibles y convenientes.

Compacto y ligero = más fácil de sostener

Diámetro: 26 mm x 26 mm Longitud: 200 mm Peso: 148 g

Dispositivo Fi-P:

• Tiempo de calentamiento de 0,2 segundos
• Punta flexible de 0,35 mm
• Control de temperatura de alta precisión
• 4Temperaturas de trabajo
• 4 horas de resistencia
• Base de carga con diseño de monitoreo de temperatura de batería. 

El paquete Fi-P incluye:

Fi-P: WP4004, WP4504, WP5506, WP5508

*Puntas adicionales/diferentes que se venden por separado

El paquete Fi-E incluye:

E23G-M (Longitud 24 mm), E25G-L (Longitud 28 mm) x2, E23G-L (Longitud 28 mm)

*Puntas adicionales/diferentes que se venden por separado

A continuación te dejamos algunos videos para que los veas. ¡Disfrútalos!

1. How many times can the Work Tip be autoclaved?
The Work Tip can be autoclaved up to 100 times. Each cleaning, disinfection, and sterilization cycle should be documented.

2. What should I do if the Work Tip shows visible stains after cleaning and disinfection?
If visible stains are present, you should repeat the entire cleaning and disinfection process to ensure the Work Tip is thoroughly cleaned.

3. What temperature should not be exceeded when cleaning the Work Tip?
The Work Tip should not be exposed to temperatures above 138°C during cleaning, disinfection, or sterilization.

4. What are the steps for post-operative treatment of the Work Tip?
Turn off the Heating Handpiece and let it cool for 1 minute.
Use a cotton swab or clean soft cloth to remove any remaining Gutta-percha.
Dry the Work Tip with a clean, soft cloth and place it in a clean tray.

5. How should the Work Tip be prepared before cleaning?
Remove the Work Tip Protector and place it in a clean tray.
Remove the Work Tip from the handle and place it in a clean tray.
Wipe the Work Tip with a soft cloth to remove visible dirt, then dry it with a clean cloth and place it in a clean tray. Use pure water for cleaning.

6. What is the recommended procedure for cleaning the Work Tip?
Pre-wash with pure water at 25°C for 3 minutes.
Clean with a detergent recommended by the manufacturer (e.g., RUHOF ENDOZIME AW PLUS WITH APA) at 25°C for 5 minutes.
Rinse twice with pure water at 25°C for 1 minute each.

7. How should the Work Tip be disinfected?
Disinfection should be performed no later than 2 hours after cleaning. Use an automated washer-disinfector set to 93°C for 5 minutes with an A0 value greater than 3000.

8. What are the drying methods for the Work Tip if not using automatic drying?
Dry with filtered dry compressed air (max pressure 3 bar) until no liquid is visible on white paper or cloth.
Alternatively, dry in a medical drying cabinet or oven at 80°C–120°C for 15–40 minutes.

9. What should be done if the Work Tip shows damage?
If the Work Tip is damaged, such as being smashed or corroded, it must be discarded and not used further.

10. How should the Work Tip be stored after sterilization?
Store the sterilized Work Tip in a medical sterilization bag or clean sealing container, and keep it in a special storage cabinet. The storage time should not exceed 7 days; otherwise, reprocess before use.