Dispositif d'obturation Woodpecker / DTE Gutta-percha Fi-E & Fi-P Plus (Blanc)

Appareil Fi-E :

Sans fil et électrique

Fluidité parfaite de la gutta-percha, sortie de gutta-percha uniforme et lisse sans bulles. Plus facile que l'injection manuelle traditionnelle de gutta-percha pour soulager la fatigue des mains de l'opérateur. Élimination des risques chirurgicaux liés aux fuites et débordements de gutta-percha. Entretien grâce au nettoyage automatique de la gutta-percha restante.

Aiguille d'injection réutilisable

Rotation à 360°. 3 vitesses d'injection. La barre de gutta-percha est directement chargée dans l'aiguille d'injection. Il n'y a aucun résidu de gutta-percha à l'intérieur de la machine, ce qui facilite le nettoyage. La barre de gutta-percha peut être remplacée à tout moment sans attendre le refroidissement interne de la machine.

Conception à deux boutons

Boutons d'injection doubles conçus symétriquement, sensibles et pratiques.

Compact et léger = plus facile à tenir

Diamètre : 26 mm x 26 mm Longueur : 200 mm Poids : 148 g

Appareil Fi-P :

• Temps de chauffe de 0,2 s
• Pointe pliable de 0,35 mm
• Contrôle de température de haute précision
• 4Températures de fonctionnement
• 4 heures d'endurance
• Base de chargement avec conception de surveillance de la température de la batterie 

Le forfait Fi-P comprend :

Fi-P : WP4004, WP4504, WP5506, WP5508

* Embouts supplémentaires/différents vendus séparément

Le forfait Fi-E comprend :

E23G-M (longueur 24 mm), E25G-L (longueur 28 mm) x 2, E23G-L (longueur 28 mm)

* Embouts supplémentaires/différents vendus séparément

Voici quelques vidéos à visionner. Bonne lecture !

Fi-E + Fi-P Plus PDF Catalogue

1. How many times can the Work Tip be autoclaved?
The Work Tip can be autoclaved up to 100 times. Each cleaning, disinfection, and sterilization cycle should be documented.

2. What should I do if the Work Tip shows visible stains after cleaning and disinfection?
If visible stains are present, you should repeat the entire cleaning and disinfection process to ensure the Work Tip is thoroughly cleaned.

3. What temperature should not be exceeded when cleaning the Work Tip?
The Work Tip should not be exposed to temperatures above 138°C during cleaning, disinfection, or sterilization.

4. What are the steps for post-operative treatment of the Work Tip?
Turn off the Heating Handpiece and let it cool for 1 minute.
Use a cotton swab or clean soft cloth to remove any remaining Gutta-percha.
Dry the Work Tip with a clean, soft cloth and place it in a clean tray.

5. How should the Work Tip be prepared before cleaning?
Remove the Work Tip Protector and place it in a clean tray.
Remove the Work Tip from the handle and place it in a clean tray.
Wipe the Work Tip with a soft cloth to remove visible dirt, then dry it with a clean cloth and place it in a clean tray. Use pure water for cleaning.

6. What is the recommended procedure for cleaning the Work Tip?
Pre-wash with pure water at 25°C for 3 minutes.
Clean with a detergent recommended by the manufacturer (e.g., RUHOF ENDOZIME AW PLUS WITH APA) at 25°C for 5 minutes.
Rinse twice with pure water at 25°C for 1 minute each.

7. How should the Work Tip be disinfected?
Disinfection should be performed no later than 2 hours after cleaning. Use an automated washer-disinfector set to 93°C for 5 minutes with an A0 value greater than 3000.

8. What are the drying methods for the Work Tip if not using automatic drying?
Dry with filtered dry compressed air (max pressure 3 bar) until no liquid is visible on white paper or cloth.
Alternatively, dry in a medical drying cabinet or oven at 80°C–120°C for 15–40 minutes.

9. What should be done if the Work Tip shows damage?
If the Work Tip is damaged, such as being smashed or corroded, it must be discarded and not used further.

10. How should the Work Tip be stored after sterilization?
Store the sterilized Work Tip in a medical sterilization bag or clean sealing container, and keep it in a special storage cabinet. The storage time should not exceed 7 days; otherwise, reprocess before use.