Woodpecker Endo 3 - Ultrasonic Endo Activator Device

1. Can the Woodpecker Endo 3 be used with disposable polymer tips in a dry root canal?
No, the root canal should not be dry when using disposable polymer tips with the Woodpecker Endo 3. It is crucial that the canal is kept wet with an irrigation solution (e.g., sodium hypochlorite or EDTA) to maximize cleaning efficiency and avoid potential issues like heat generation or tip damage.

2. Why is it important for the root canal to be wet during ultrasonic activation?
Using the Endo 3 in a wet root canal enhances cleaning by:
Promoting acoustic streaming and cavitation, which help dislodge debris, biofilm, and bacteria.
Preventing heat generation that can occur during ultrasonic activation in a dry canal, reducing the risk of tissue damage or tip degradation. Allowing better irrigant penetration into complex areas like lateral canals and isthmuses.

3. What irrigation solutions should be used with the disposable polymer tips?
Common irrigation solutions such as sodium hypochlorite and EDTA are typically used during ultrasonic activation. These solutions, when activated by the polymer tips, improve the effectiveness of the cleaning and debridement process.

4. What happens if I use the disposable polymer tip in a dry root canal?
Using the polymer tip in a dry canal can result in:
Increased friction, leading to faster wear or damage to the tip. Potential heat generation, which could harm the surrounding tissues or cause the tip to deteriorate.
Reduced cleaning efficiency, as the ultrasonic energy will not be properly transmitted without fluid to activate.

5. Does keeping the canal wet affect the longevity of the disposable polymer tips?
Yes, keeping the canal wet during activation helps extend the lifespan of the polymer tips by reducing friction with the canal walls and preventing overheating, which can wear down the tips prematurely.

6. How do I ensure the canal stays wet during activation?
Before activating the disposable polymer tips with the Endo 3, ensure the canal is properly irrigated with your chosen solution. Periodically replenish the irrigant if necessary during the activation process to maintain a wet environment.

General FAQs:
7. How do I switch between different modes on the Endo 3 Ultrasonic Endo Activator?
To switch modes, press the mode switching button. The device has three modes: shutdown mode, hot standby mode (for power and time adjustments), and irrigation mode (working mode).

8. What should I do if the device doesn’t turn on?
If there is no indication or action:
The battery might be low. Connect the device to the power supply to charge. If the battery is damaged, it needs replacement. If used continuously for a long time, the thermal protection circuit might be triggered. Let the device cool down for a few minutes before using it again.

9. How long does it take to charge the Endo 3, and how long does the battery last?
It takes about 4 hours to fully charge the device, and it can operate for approximately 1 hour on a full charge.

10. What should I do if the device doesn’t charge after connecting to the power adapter?
Check if the power supply is connected properly. Reconnect if needed. Ensure the power adapter is working and matches the device specifications. Clean the thimble on the charging base using ethyl alcohol to remove any impurities.

11. How do I clean and disinfect the Endo 3 device components?
After each use, wipe all surfaces of the tip, host, and protective silicone cover with a soft cloth and pure water. For disinfection, follow automated disinfection procedures using a washer-disinfector if available.

12. How often should the tips, Endo wrench, and protective silicone cover be sterilized?
The tips, Endo wrench, and protective silicone cover must be sterilized before each treatment. The tip can be sterilized up to 300 times, the wrench up to 1,000 times, and the protective silicone cover up to 300 times.

13. What kind of sterilization procedure should I follow for the Endo 3 tips and accessories?
Use steam sterilization (fractional pre-vacuum procedure) at 134°C for 5 to 20 minutes. Avoid hot air or radiation sterilization, as they may damage the product.

14. What should I do if the device’s tips are not working properly?
If the tips are malfunctioning, it could indicate a problem with the host. Contact the manufacturer or local dealer for maintenance and inspection.

15. Why does the battery last for a shorter time after charging?
If the battery’s capacity has decreased over time, it may need servicing or replacement. Contact the maintenance department for further assistance.

16. How should I store and handle the Endo 3 to ensure its longevity?
Always clean the device before and after each operation. Ensure that the tip is tightly screwed, and avoid striking or scratching the host. Use only Woodpecker or DTE branded tips to avoid potential damage.